Operation Instruction
BAKER Three proofing paint 2101 is the synthesis of new materials used in waterproofing, insulation, protection plastic solvent which is excellent alternatives of imported products currently, used for printed circuit boards, electronic components moisture-proof, anti-mold, anti-corrosion, Defense parts and loose insulation.
Color : transparent
Transparency : 99.9%
Mixing ratio : 10:3
Use Time : 25°C 400g five-hour
Curing time: 25℃ an hour
Viscosity : 25°C 80CPS mixed 450CPS just five hours
Proportion : 25°C
0.95± 0.01
Flash point : 580F
2．Technical Parameters
Before Curing | test
| 2101 |
color
| transparent |
Viscosity （Pa.s）
| 80 |
non-volatile content
| >85% |
Density （g/cm3）
| 1.05 |
25℃dry time (min)
| 30--60 |
After curing
| Mechanical properties | tensile strength (Mpa)
| 5.5 |
elongation at break (%)
| 350 |
hardness
(shore A)
| 85 |
shear strength (Mpa)
| 3.5 |
peel strength (N/mm)
| >20 |
Dielectric Properties | intensity (kv/mm)
| 21 |
constant (@60Hz)
| 3.0 |
loss factor (@60Hz)
| 5×10-3 |
Volume resistivity(Ω·cm)
| 5×1016 |
Thick resistance | Grindability | Sard70 pencil hardness HB
| Scratch |
Softness | bending 1/8m
| no crack |
Water resistance | at 100°C and 98-100% relative humidity
| same hardness in 30days |
Mildew resistance | No nutrients |
Note : all mechanical and electrical properties at 25 ° C, humidity 55% under the conditions of curing measured seven days.
3 Operation Methods
（1）Main solvent and curing solvent mixed by 10:3:10 in measuring cup
（2）Add glue in a containers larger than the pieces.
（3）Pieces soak in the glue within 2-5 seconds.
（4）Taking out the dipped piece slowly and tilting,making surplurs glue flow .
（5）Puting pieces horizontal on the absorbent paper (small pieces) or a trestle (bulky), curing in 1 hour
（6）Checking the surface, if were not covered by glue,make it perfectly.
（7）Staying 24 hours and painting finished, packaging.
4 Operation Notes
（1）Before spraying PC boards or electronic ,the surface should be dealed with (to get rid of oil and dust) in order to make glue more efferctiveness.
（2）The materials include 2101A,2101B and 2101C components
（3）Brushing spraying,dip-coating can be chosed,diluted with 2101 C
（4）Mixed A : B = 10:3 and if required thinner brush or spraying ,using 2101 C.Mixing ratio A100 + B30 + 100 C
（5）If do the twice then should wait until the first cover dry.
（6）expiration date:12 months (stored in cool,dry places)
Three proofings paint
Three proofings paint is a kind of special paint,used in protecting PCB and other related equipments from the harm of environment Thereby enhancing their duration and ensuring the safety and reliability.
Three proofing paint used as PCB coating, forming a light and flexible flim only 25 -50 microns thick. It can protect circuits from chemical substances (for example : fuel, cooling, etc.), vibration, moisture, salt spray, humid and high temperature under which conditions PCB likely to be corroded, mold growth and short-circuit.
Benefits:
Three proofing paint film can effectively isolate and protect circuits against chemicals, moisture and dirt erosion, thereby enhancing the reliability of circuit boards to increase their safety coefficient as well as its lifespan. Because Three proofing paint can prevent electricity
leakage, thus allowing a higher power and the more smaller PCB space. So the smaller components can meet the need. Both transparent and colored Three proofing paint can improve the appearance of circuit board, and the latter covered the layout and design of components can guarantee a higher degree of confidentiality
Typical use
At first Three proofing paint applies only to the high-tech field of printed circuit boards. Now consumers are increasingly concerned about the quality and reliability of the products .what’s more the electronic devices has been more widely used in daily life.Using Three proofing paint can improve product quality and consistently reduce the warranty-period repair costs. Typical uses include the following areas
Civilian and commercial uses
Three proofing paint can be used for household electronic circuits protection so that they can resist :
Water and detergent (such as : laundry machines and dishwashers)
High humidity (such as microwave ovens)
Chemical environment (such as : washer / dryer)
Office and the family of harmful substances (such as computers)
The adverse external environment (such as : Burglar Alarm Device)
Automobile industries
Three proofing paint used in Automobile industries will protect circuit from the following types of hazards, such as : gasoline vapors. salt spray / brake fluid and so on. Electronic systems applied in motor vehicles is growing rapidly. Therefore, using the Three proofing paint has become the basic requirement of electronic device to ensure long-term reliability. Three proofing paint applied to the following aspects :.
Machine enclosures (eg : Engine Management System)
Passenger vehicle (Add : Inside the computer control system)
Aerospace and aviation
Aerospace and aviation environment have strict requirements of the electronic equipment in terms of the rapid changes of pressure which have the impact on circuit performance. So it is a must to use the Three proofing paint widely. Three proofing paint can be applied to the following areas :
Pressure reducing: (eg: flight line control system).
Cabin (eg : air conditioning system)
Navigation
Both fresh water and salt water will cause harm to the electrical equipment shipping circuits. The use of Three proofing paint can protect the equipment on the surface effectively and for the underwater equipment, the use of resin to protect is a must also. Typical applications include: Navigation system
Radar Control System
Medical / industrial
Medical / industrial using Three proofing paint to protect the equipment from the adverse external environment.It is used widely
including :
Tools - to prevent corrosion and easy to store.
Agricultural machinery – prevent pacemaker pollution from fertilizers and field wastes to ensure continuous stability
